Dyson Washing Machine Error Codes
Washing Machine is useful Product from Every home And it is a product used in every home Sometimes it contains an error code. We can fix some error codes at home and we need to call a technician to fix some error codes. In this post you will find all the error codes of Dyson washing machine and I hope you will benefit a lot from this post. If you find it helpful, please share this post.
| Error Codes | Meaning |
|---|---|
| F1 | Drum overloaded |
| F2 | Out of Balance |
| F3 | Outer Door open |
| F4 | Inner Door open |
| F5 | Not draining |
| F6 | Not filling |
| F7 | Tacho open circuit |
| F8 | Overfilling |
| F9 | Not used |
| F10 | Over speed (motor triac failure) |
| F11 | No Motor action |
| F12 | Invalid temp signal |
| F13 | Not heating |
| F14 | Flooding |
| F15 | Gear change failure (too slow) |
| F16 | Not stopping ( motor triac failure) |
| F17 | Not used |
| F18 | Gear change failure (too quick!) |
Dyson Washing Machine Troubleshooting
| Symptom | Possible causes and Solutions |
|---|---|
| LCD display is blank | There is no power to the machine. Ensure the machine is plugged in and switched on. Check the fuse and also that the circuit breaker has not tripped. |
| Certain spin speeds, temperatures or soil types cannot be selected | There are limits set on these options for each programme to prevent unsuitable options being selected. |
| Cannot open outer door | Machine has not finished the cycle. Wait for the machine to finish the cycle before opening the door. To cancel the wash hold down the ‘Cancel’ button. |
| Machine has paused and the water level is too high or the water is too hot. Press ‘Start’ to resume the wash. | |
| Child lock is active. Hold down the ‘Minimum iron’ button until ‘Child lock off’ is shown on LCD. | |
| Power cut or any other cause not listed above. | |
| Machine leaks water | Coin trap cover is not in place, or the plug is not closed. Turn off the water supply to the machine and ensure that the coin trap cover is correctly fitted and that the plug is closed. |
| Machine is not level. Adjust the feet until the machine is level. | |
| Drainage hose is not connected correctly. Check the drainage hose is draining into a suitable place (drain, sink or standpipe). | |
| Inlet hoses are not positioned or correctly fitted. Ensure the hoses are fitted correctly. | |
| Soap tray is open. Close the soap tray. | |
| Machine shakes during the cycle | 2 adjustable front feet are not level. Adjust feet until the machine is level. |
| Rollerjack handle has not been replaced under the machine. Return the Rollerjack handle carefully to its position under the machine. | |
| Burning smell | Transit packaging not removed. Remove top, rear and front packaging. |
| Clothes warm at end of cycle | Hot and cold pipes reversed. Check orientation of hot and cold pipes. |
| Child lock on | The child lock has not been deactivated. Hold down the ’Minimum iron’ button until ‘Child lock off’ is shown on the LCD. |
| Overload reduced performance | The recommended wash load has been exceeded or unusual items have been washed. The wash load is uneven. |
| Uneven load could not spin | The machine sensed that spinning would be unsafe. Unusual items eg: trainers may have been washed. Remove some items or reload the machine and select ‘Spin only’. |
| Close outer door then press start | Outer door not closed properly, manual release still open. Close the outer door, ensuring nothing is trapped. Turn manual release clockwise. |
| Close inner door then press start | Inner door not closed properly. Close the inner door, ensuring nothing is trapped. |
| Not emptying: check hose and coin trap | Coin trap blocked. Remove blockages. |
| Machine full of suds. Leave suds to settle. In future, refer to the manufacturer’s dosage instructions. | |
| Drainage hose not draining. Check that the drainage hose is installed according to the installation instructions. | |
| Not filling: check water supply | Water supply is not connected. Check that the water supply is connected and turned on at the tap. |
| Filter is blocked. Clean the filters. | |
| Inlet hoses are blocked or kinked. Unblock or straighten the inlet hoses. | |
| Drainage hose is installed incorrectly. Unblock or straighten the drainage hose. | |
| Flood protection hose (Memory only). Fitted back to front. |
Dyson Washing Machine Manual PDF
