0

Samsung Automatic Washing Machine Error Codes

Samsung Automatic Washing Machine Error Codes

Samsung Automatic Washing Machine Error Codes

Washing Machine is useful Product from Every home And it is a product used in every home Sometimes it contains an error code. We can fix some error codes at home and we need to call a technician to fix some error codes. In this post you will find all the error codes of Samsung washing machine and I hope you will benefit a lot from this post. If you find it helpful, please share this post.

ERROR IMAGEMEANINGSOLUTION
Unbalanced load prevented your Washer from spinning.Redistribute the load, press the Start/ Pause Button.
Door is unlocked when Washer is running.Press the Power button to turn off your Washer, then restart the cycle. If the code reappears, call for service.
Door is open when Washer is running.Close the door tightly and restart the cycle. If the code reappears, call for service.
Your Washer failed to lock the door.Close the door tightly and restart the cycle. If the code reappears, call for service.
Water temperature control problem. (Heater Control problem)Call for service.
Your Washer has tried to fill but has not reached the proper water level.Call for service.
Water level sensor problem.Call for service.
The door will not unlock.Make sure the door is firmly closed. Push the Power button to turn off your Washer, then turn it on again. If the code reappears, call for service.
Your washer is not draining. It can also mean that the unit senses a small clog while draining.1) Turn off the unit and turn it on again. 2) Select only the Spin Cycle. 3) Press the Start/Pause to drain the water.
Your Washer has tried to fill but was unsuccessful.Make sure the water faucets are open all the way. Check for kinked hoses. Check the inlet screens on the fill hoses.
Problem with control.Call for service.
A fault is detected in the water level sensor.Call for service.
Jammed Key.Call for service.
• Motor speed sensor problem. • High current detected. • Motor not running properly.Restart the cycle pressing the Start/ Pause Button. If the code reappears, call for service.
Temperature sensor problem.Restart the cycle. If the code reappears, call for service.
High/Low voltage detected.Restart the cycle. If the code reappears, call for service.
SilverCareTM control problemRestart the cycle. If the code reappears, call for service.
Too many suds are detected during the washing session.To prevent it, cut down on detergents.

Solution: Check the electronic control board

Error CodeCauseRepair
E2Stuck key on control boardTry to free the key by gentle force. If you can’t free the key, replace the user interface control board (also called the sub-PCB control board).
lEWater level sensor failureFirst, unplug the washer and check the wire harness connections between the water level sensor and the main control board.
nFWater fill problemIf the washer takes 40 minutes or more to fill or if the water level doesn’t change after six minutes, this code will appear.
LO or FLDoor lock errorOnce the washer cycle is complete if the door fails to unlock after seven tries, you’ll get the LO or FL code
dcUnbalanced loadhe dc code means the load has been detected as unbalanced during the final spin.
dsDoor is not lockedIf the washer won’t start ds signals that the washer door is open and the lock is malfunctioning.
OEOverflow or too high water levelsA washer that is overfilled is usually caused by water inlet valves that are not shutting off the water flow properly.
nF1Hot and cold water lines are reversedConnect the hot and cold water fill hoses correctly on the back of the washer.
tEWater temperature is either too high or too lowRun the diagnostic test mode to check the water temperature that the control board is sensing. If the actual temperature is significantly different, the temperature sensor or thermistor should be replaced.
LELow water level during cyclesWater level drops can be caused by leaks in the washer tub or an improperly installed drain line which can siphon water out of the washer.
3ENo signal from the drive motor tachometerUnplug the washer. Check the wire harness connections on the drive motor and the electronic control board.
HrHeater relay failureThe heater relay is a component on the Main PCB control board.
2EInternal control board failureUnplug the washer for 5 minutes to reset the electronic control board. Plug the washer back in.
SFMain PCB errorUnplug the washer for five minutes to reset the electronic control board.
ndWater will not drainIf the washer fails to drain within 15 minutes, check the washer drain filter and drain hose for a clog or restriction.
Sud (F70)Too many sudsUsing a regular detergent or even too much high-efficiency (HE) detergent will produce excessive suds.
AECommunication error between the Main PCB and Sub PCB in the control panelCheck the wire harness connections between the PCB control boards in the control panel.

Samsung Washing Machine Troubleshooting

ProblemAction
Stops.• Plug the power cord into a live electrical outlet. • Check the fuse or reset the circuit breaker. • Close the door and press Start/Pause to start the washing machine. For your safety, the washing machine will not tumble or spin unless the door is closed. • Before the washing machine starts to fill, it will make a series of clicking noises to check the door lock and does a quick drain. • There may be a pause or soak period in the cycle. Wait briefly and the washing machine may start. • Make sure the mesh filter of the water supply hose at the water taps is not clogged. Periodically clean the mesh filter. • If the washing machine is not supplied with sufficient power, the washing machine temporarily will not drain or spin. As soon as the washing machine regains sufficient power, it will operate normally.
Fills with the wrong water temperature.• Fully open both taps. • Make sure the temperature selection is correct. • Make sure the hoses are connected to the correct taps. Flush water lines. • Make sure the water heater is set to supply a minimum 120 °F (49 °C) hot water at the tap. Also, check the water heater capacity and recovery rate. • Disconnect the hoses and clean the mesh filter. The mesh filter may be clogged. • While the washing machine fills, the water temperature may change as the automatic temperature control feature checks incoming water temperature. This is normal. • While the washing machine fills, you may notice just hot and/ or just cold water going through the dispenser when cold or warm temperatures are selected. This is a normal function of the automatic temperature control feature as the washing machine determines the water temperature.
Load is wet at the end of a cycle.• Use the High or Extra High spin speed. • Use high efficiency (HE) detergent to reduce oversudsing. • Load is too small. Small loads (one or two items) may become unbalanced and not spin completely. • Make sure the drain hose is not kinked or clogged.
Leaks water.• Make sure the door is properly closed. • Make sure all hose connections are tight. • Make sure the end of the drain hose is correctly inserted and secured to the drain system. • Avoid overloading. • Use high efficiency (HE) detergent to prevent oversudsing.
Has odours.Excessive suds collect in recesses and can cause foul odours. • Run cleansing cycles to sanitize periodically. • Clean the door seal (diaphragm). • Dry the washing machine interior after a cycle has finished.
No bubbles are seen (Bubbleshot models only).• Overloading may screen bubbles. • Severely contaminated laundry may not generate bubbles.
Can I open the Add Door at any time?The Add Door can be opened only when the indicator appears. However, it does not open in the following cases: – When the boiling or drying process is running and the internal temperature becomes high. – If you set the Child Lock for safety reasons. – When the drum wash or drum drying cycle is running that does not involve additional laundry.

Samsung Washing Machine Manual PDF

Whirlpool Refrigerator ARB-884SGYS Electric Diagram

HVAC Solution