Daewoo Washing Machine Error Codes
Washing Machine is useful Product from Every home And it is a product used in every home Sometimes it contains an error code. We can fix some error codes at home and we need to call a technician to fix some error codes. In this post you will find all the error codes of Daewoo washing machine and I hope you will benefit a lot from this post. If you find it helpful, please share this post.
| Error Code | Problem |
|---|---|
| F1 | The machine turns on but does not start and LEDs No. 1 and 2 flash ( LED model) or F1 appears on display (LCD model) |
| F2 | The machine does not take water and LEDs. 1 and 3 flash (LED model) or F2 appears on display (LCD model) |
| F3 | LED number 2 and 3 flash (LED model) or F3 appears on monitor (Display model) |
| F4 | The machine does not empty, does not spin and LED 1 and 4 flash (LED model) or F4 appears on display (LCD model) |
| F5 | LED number 2 and 4 flash (LED model) or F5 is displayed (Display model). |
| F6 | LED number 1, 2 and 4 flash (LED model) or F6 is displayed (Display model). |
| IE | Water inlet error |
| OE | Drain error |
| UE | Unbalance error. The laundry is concentrated to one side of the drum during spin. Rearrange the laundry. |
| LE | Door open error |
| E2 | Overflow error |
| E4 | Leakage error. Water leaks from the tub or the hose drain. Check the leak of the tub or the hose drain. Then change the tub or the hose drain. |
| E5 | High voltage error |
| E6 | EMG error |
| E8 | Motor error |
| E9 | Sensor pressure error. The water level sensor is an inferior product. Change the water level sensor. |
| H2 | Thermistor wash error |
| H4 | Thermistor wash overheating error |
| H5 | Water temp. Error |
| H6 | Heater wash error |
| H8 | Heater wash overheating error. The heater worked without the water in the tub. Check the water level and the heater wash. |
| lb | LGBT error. The pcb ass’y is an inferior product. Change the pcb ass’y. |
| PFE | Pump filter error |
| b1 | Motor alignment error |
| b2 | Motor speed control error |
| b3 | Low voltage error |
| b4 | Motor startup overloading error |
Daewoo Washing Machine Troubleshooting
| Problem | Possible Solution |
|---|---|
| The door does not open | Make sure the red pilot lamp turns off Make the special function SOAK or RINSE HOLD is not activated Push the door from the door locking side or give a slight tap and at the same time pull it to open |
| The is water on the floor | Make sure the red pilot lamp turns off Make the special function SOAK or RINSE HOLD is not activated Push the door from the door locking side or give a slight tap and at the same time pull it to open |
| The washing machine pelting in water even when it is off | Make sure the red pilot lamp turns off Make the special function SOAK or RINSE HOLD is not activated Push the door from the door locking side or give a slight tap and at the same time pull it to open |
| The machine vibrates noticeably | Ensure that the transportation screws have been removed during installation Ensure using the correct detergent for washing machine Make sure that the laundry is not amassed or knotted and that the spin speed is adequate for the laundry load. It so recommended that for excessive laundry load and less than half the nominal load capacity set the spin speed to low Make sure the drain pump filter is not clean. Ensure that the drain pump is squashed and that the machine dranins effectively Ensure that the machine is properly levelled on floor. It is recommeded that for any eventual feet imbalance compensation the feet must regulated and lock them in place with the locking knob ( see figure on page 10) |
| The machine does not turn on or start | Make sure that the power plug is inserted. Make sure there is power in the socket. Make sure that the selector switch, programme selector knob 1, is not in the OFF position. |
Daewoo Washing Machine Manual PDF
