0

Whirlpool Washing Machine Error Codes

Whirlpool Washing Machine Error Codes

Whirlpool Washing Machine Error Codes

Washing Machine is useful Product from Every home And it is a product used in every home Sometimes it contains an error code. We can fix some error codes at home and we need to call a technician to fix some error codes. In this post you will find all the error codes of Whirlpool washing machine and I hope you will benefit a lot from this post. If you find it helpful, please share this post.

Digital display codes

Error Code : F01 – Electronic circuit board fault

Issue: Washing Machines is not operating – some or all functions are not selectable.

Advice: We recommend you disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply and wait 30 seconds and try starting the machine again.

Advice: If the fault remains, please call our customer service center to book an engineer on: 0344 822 4224

Error Code : F02 — Motor circuit fault

Issue: Intermittent or no drum rotation during wash cycle.

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

Error Code : F03 — Temperature sensing fault

Issue: Washing Machines not heating on wash or dry settings.

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

Error Code : F05 — Waste pipe blockage or pump issue

Issue: Washing Machines door will not open / the door can be opened but water remains inside the drum.

Advice: Please check for blockages in your pump filter (if applicable to model – please see user handbook). Also check for any blockages in waste water hose and in any under-sink plumbing. If none of the above solutions work, it is likely you have a pump failure and will need further assistance.

Advice: If the fault still remains then we recommend you call our customer service center to book an engineer on: 0344 822 4224

Error Code : F06 — Door lock fault

Issue: Washing Machines door cannot be opened or closed / when the door is closed the machine the program will not start.

Advice: If your washing machines door will not close, please check for any obstructions in the door lock. If the fault still remains then we recommend you call our customer service center to book an engineer on: 0344 822 4224

Error Code : F07 — Electronic circuit board fault / heating circuit fault

Issue: During a wash cycle the program pauses part way through/ the machine is not heating and the pump runs continuously.

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

Error Code : F08 — Heater fault

Issue: During a wash cycle the program pauses part way through.

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

Error Code : F09 — Software fault

Issue: Washing Machines isn’t operating multiple flashing lights and/or display. Unable to select a program.

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

Error Code : F11 — Pump circuit fault

Issue: Water remains in Washing Machines / not pumping out.

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

Error Code : F12 — Electronic control fault

Issue: Washing Machines is not operating (turning on).

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

Error Code : F13 — Dryer temperature sensing fault (washer dryers only)

Issue: Washer dryer is not drying clothes.

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

Error Code : F15 — Heater control fault (Washing Machine and Washer Dryers)

Issue: Washing Machines is not heating water or pauses during a wash cycle / not drying or pauses during drying cycle.

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

Error Code : F16 — Drum lock position sensor fault (top loading machines only)

Issue: Washing Machines drum is stopping in the wrong position or is not locked in the correct position.

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

Error Code : F18 — Internal data error

Issue: Some or all display / functions do not work on my washing machines.

Advice: Please disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply, wait 30 seconds and try starting the machine again.

Advice: If the fault remains, we recommend you call our customer service center to book an engineer on: 0344 822 4224

Error Code : F19 — Fan motor or heating fault (washer dryers only)

Issue: Washing Machines is not drying / stops during drying cycle.

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

Flashing LED codes

If your Whirlpool washing machine have not display then we can fix error code with blinking light. Whirlpool washing machine have 5 light.

If Blinking : LED1

Heater fault

Issue: During a wash cycle the program pauses part way through.

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

If Blinking : LED1 + LED2

Electronic control fault

Issue: Washing Machines is not operating (turning on).

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

If Blinking : LED1 + LED2 + LED3 + LED4

Heater control fault (Washing Machine and Washer Dryers)

Issue: Washing Machines is not heating water or pauses during a wash cycle / not drying or pauses during drying cycle.

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

If Blinking : LED1 + LED2 +  LED4

Dryer temperature sensing fault (washer dryers only)

Issue: Washer dryer is not drying clothes.

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

If Blinking : LED2

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

If Blinking : LED2 +  LED3

Door lock fault

Issue: Washing Machines door cannot be opened or closed / when the door is closed the machine the program will not start.

Advice: If your washing machines door will not close, please check for any obstructions in the door lock. If the fault still remains then we recommend you call our customer service center to book an engineer on: 0344 822 4224

Safety Notice: A recall has been launched relating to the door lock system for certain Hotpoint and Andesite washing machines. Find out more here.

If Blinking : LED2 +  LED3 + LED4

Electronic circuit board fault / heating circuit fault

Issue: During a wash cycle the program pauses part way through/ the machine is not heating and the pump runs continuously.

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

If Blinking : LED3 

Motor circuit fault (flashing light)

Issue: Intermittent or no drum rotation during wash cycle.

Internal data error (static light)

Issue: Some or all display / functions do not work on my washing machines.

Advice: Please disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply, wait 30 seconds and try starting the machine again.

Advice: If the fault remains, we recommend you call our customer service center to book an engineer on: 0344 822 4224

If Blinking : LED3 + LED4

Temperature sensing fault

Issue: Washing Machines not heating on wash or dry settings.

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

If Blinking : LED4

Electronic circuit board fault

Issue: Washing Machines is not operating – some or all functions are not selectable.

Advice: We recommend you disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply and wait 30 seconds and try starting the machine again.

Advice: If the fault remains, please call our customer service center to book an engineer on: 0344 822 4224

If Blinking : LED5

Drum lock position sensor fault (top loading machines only)

Issue: Washing Machines drum is stopping in the wrong position or is not locked in the correct position.

Advice: We recommend you call our customer service center to book an engineer on: 0344 822 4224

Whirlpool Refrigerator ARB-884SGYS Electric Diagram

HVAC Solution